Guides

How to Clear Your Driveway With a Remote Control Snow Plow

Mowrator S1 4WD with a snow plow clearing a paved driveway beside a two-car garage.
Sarah Jenkins
Written by
Reviewed byMarcus Chen

Plan easier driveway snow clearing with a remote control snow plow. Learn where to pile snow, how to organize passes, and which Mowrator S1 4WD setup fits your property.

Share
X Facebook Pinterest

A remote control snow plow lets you guide the machine without riding on it or walking behind a shovel. But a clear driveway takes more than pushing forward: you need somewhere to put the snow, room to turn, and a route that keeps the garage and front walk accessible.

For a typical American home with a garage apron, parked vehicles, and a driveway leading to the street, the most useful plan is often a series of short pushes toward designated storage areas. Here is how to plan those passes and decide whether a Mowrator S1 4WD snow-plow setup fits your property.

First, Match the Setup to Your Driveway

Walk the area before snow covers the pavement. Note the driveway surface, its narrowest point, changes in grade, and any raised joints or gravel transitions. Mark edges and obstacles that will be hard to see later.

A plow needs room beside the cleared route to leave the snow. If your driveway is hemmed in by walls, parked cars, or existing snowbanks, that storage space may matter more than driveway length.

For Mowrator owners, the Snow Plow Kit is compatible with the S1 4WD, not the S1 2WD. The battery-powered mower becomes a remotely controlled snow-pushing machine with the attachment installed. It remains under your active control throughout the job.

Before operating, check the current equipment manual for your attachment version, snow conditions, approved traction equipment, and operating limits. A mower’s grass-slope rating is not a snow-plowing rating.

Pick Snow Storage Areas Before You Start

Choose open areas on your own property where snow can remain without blocking access. Look beyond today’s clearing: a pile needs space to grow during later storms, and meltwater needs a route away from the house and cleared pavement.

Keep these areas open:

  • Garage doors and the space needed to maneuver vehicles.
  • The front walk, steps, gates, and public sidewalk.
  • Storm drains, drainage channels, and their runoff paths.
  • Fire hydrants, mailboxes, and driveway sightlines.

Keep snow out of the street and off neighboring property. Wellesley’s snow-removal recommendations, for example, advise against moving driveway snow into or across the road or onto the sidewalk. Check your own town’s requirements for local clearing duties.

One useful check: imagine backing a vehicle out after the pile has doubled in size. Would you still see approaching traffic and have room to turn? If not, choose another storage area.

Clear in Sections Instead of Making One Long Push

The goal is to move each small load into storage without collecting more snow than the machine can comfortably push. Keep an open route for repositioning, and stop if the wheels lose traction or snow stops moving.

For a Two-Car Garage and Short Driveway

Start by creating working room outside the garage, with the door closed and vehicles clear of the operating area. Where there is room to position the machine, make short outward passes toward an open side of the apron.

Near a door, wall, or parked vehicle, leave a margin and finish tight areas with an appropriate hand tool. Do not assume the front blade can pull snow backward from a garage threshold.

Once the apron is open, clear the driveway in overlapping sections. Direct each section toward a side storage area rather than building a single pile at the street. Keep the connection to the front walk clear as you go.

For a Longer Driveway

Divide the driveway into shorter working sections with reachable storage areas along the way. Avoid collecting the entire length’s snow into one growing load.

If only one side offers suitable storage, set the blade to direct snow toward that side, following the attachment instructions. On return passes, reposition so you do not push snow back across the cleared lane.

Start with a small blade load. If the snow rolls or spills back into the lane, reduce the amount you take on the next pass instead of repeatedly forcing the same load forward.

Mowrator S1 4WD pushing snow toward the side of a residential driveway.

For Curves, Gates, and Walkway Connections

Clear enough space to turn before approaching a narrow section. Make smaller corrections near garage corners, fence posts, and landscaping.

Check the machine’s full width with the attachment fitted before entering a walkway or gate. A path that fits the mower alone may not fit its snow blade. Use another tool for sections that are too narrow.

Leave Room for the Next Snowfall

An RC snow plow moves snow into a pile; it does not make that pile disappear. Use the available storage area thoughtfully during the first clearing so you have somewhere to put the next snowfall.

When conditions allow, clear manageable fresh accumulation before vehicle traffic packs it down. During a prolonged storm, smaller sessions may be more practical than waiting for one deep accumulation. Pause whenever visibility, traction, or conditions make operation unsuitable.

Treat the ridge left by a street plow as a separate job. It may contain dense, compacted snow or ice even when the rest of the driveway has loose snow. Assess it before proceeding, and use equipment or a service suited to material outside your setup’s limits.

After a thaw, check where meltwater is flowing. A pile that sends runoff across the front walk may need a different storage location next time.

Plan Your Viewing Position, Too

Choose a position where you can monitor the blade, driveway edges, people, and obstacles. Move when a parked vehicle, hedge, or snowbank blocks your view.

The optional MOWFUN FPV system adds a live camera view. For homeowners considering indoor operation, the FPV Indoor Mow & Plow Bundle brings together the mower, snow plow, and FPV equipment.

Before starting from indoors, inspect the route outside and check the control and video connections in your intended operating area. Keep people and pets out of the work zone. A camera view does not show everything around the machine, and FPV does not turn the S1 into an autonomous snow-clearing robot. Stop if you lose a reliable view or control.

Homeowner using the MOWFUN FPV live view to guide a Mowrator snow plow from indoors.

Put the Same Mower to Work Beyond Grass Season

For a homeowner who also needs a mower, winter capability adds another use for the same machine. The S1 can mow during the growing season, collect leaves with its compatible bagging setup, and push snow with the Snow Plow Kit.

Choose around your property: the snow you typically get, the space available to store it, and the mowing work you need to do during the rest of the year. Review the S1 4WD Mow & Plow Bundle to see the current configuration and included equipment.

Frequently Asked Questions

Where should I put snow when plowing my driveway?

Choose an open area on your property that leaves doors, walking routes, drains, and driveway sightlines clear. Allow room for additional snowfall and consider where meltwater will go.

Is a remote control snow plow the same as a remote control snow blower?

No. A plow pushes snow with a blade; a blower collects and throws it. Mowrator S1 with the Snow Plow Kit is a plow setup. If snow needs to be thrown over existing banks or away from a confined space, compare suitable blower options.

Can I use the Mowrator Snow Plow Kit with an S1 2WD?

No. The kit is designed for the S1 4WD. Check the current product information for tire, chain, and attachment requirements before ordering.

Should I choose a riding mower plow or a remote control setup?

Consider the equipment you already own, driveway layout, available storage, and how you prefer to operate. Our riding mower snow plow vs. remote control snow plow comparison explains the main differences.

Recommended products

More to Read

Leave a comment

Please note, comments need to be approved before they are published.